CAB EOS4 Instructions d'exploitation

Conguration ManualLabel PrinterEOS

10 103 Ofine Menu3.3 Service KeyA service key is required for accessing special service functions not accessible to the operator. This key switches

10114.1 Conguration via Control Panel A host of parameters for conguring the printer are found in the Setup menu of the ofine menu.  Congure th

12 124 Conguration4.1.2 Machine Parameters  Start Ofine menu.  Select Setup > Machine param..Parameter Meaning DefaultPrinthead pos. XShiftin

12134 CongurationParameter Meaning DefaultCleaningintervalSetting of intervals for printhead cleaning in increments of 100 m media passage.If the se

14 144 Conguration4.1.3 Print Parameters  Start Ofine menu.  Select Setup > Print param..Parameter Meaning DefaultHeat levelThe Heat level se

14154 CongurationParameter Meaning DefaultError-ReprintOn: With a correctable error and corresponding troubleshooting, the label being printed when

16 164 Conguration4.1.4 Interfaces  Start Ofine menu.  Select Setup > Interfaces.Parameter Meaning DefaultNetworkConguration parameters of t

16174 Conguration4.1.5 Status LineSelect the parameters (widgets) to be displayed in Ready mode.  Start Ofine menu.  Select Setup > Status li

18 184 Conguration4.2 Conguration via the Web InterfaceThe parameters accessible via the control panel can also be set via the web interface conta

18194 CongurationStatus tabFig. 5 "Status" tab on the printer web interfaceThe following information is contained in the left top section

2 2Conguration Manual for the following productsFamily TypeEOS EOS1EOS4Edition: 06/2013 - Part No. 9009272CopyrightThis documentation as well as tran

20 204 CongurationSetup tabOn the "Setup" tab all the conguration parameters can be set which are also accessible via the control panel i

20214 CongurationThe following parameters for the Ethernet or WLAN interface can only be accessed via the web interface: Parameter Meaning DefaultHo

22 22Interpreters tabOn the "Interpreters" tab the interfaces can individually be set to the interpretation of JScript or ZPL data.Fig. 7 &

22234 CongurationNotications tabThe "Notications" tab allows to send status and error messages automatically to a SNMP manager or via e-

24 244 CongurationDevices tabThe "Devices" tab provides an overview of the most important hardware components installed in the printer and

24254 CongurationHelp menuIndependent from the chosen tab some help functions can be selected :Fig. 12 “Help” menu on the web interfaceTransmission

26 265 Test Functions5.1 OverviewThe printer is equipped with different test functions providing information on:• the most important conguration p

26275 Test Functions5.3 Status PrintThe Status print function prints a test image containing information on the conguration and status of the print

28 28The Status print contains the following information :Symbol Information• Date and time of the printout• Device type• Version and creation date

28295 Test Functions5.4 Font ListThe Font list function prints the most important parameters of the fonts available in the printer in tabular form.

23Table of Contents1 Introduction ...

30 305 Test Functions5.5 Device ListThe Device list function prints out the most important information on hardware components of the printer and con

30315 Test Functions5.6 WiFi StatusAccess only when a WLAN adapter is installed!The WiFi status function prints out a list the most important param

32 325 Test Functions5.7 ASCII Dump ModeASCII Dump Mode offers the option of checking incoming control sequences at an interface. The commands are p

32335 Test Functions5.8 Label ProleThe Label prole function carries out a longer label advance. It saves the values measured by the label sensor h

34 345 Test Functions5.9 Event LogAccess only with service key inserted!The label printer saves the following events in the Event log:• Hardware fa

34356 Service Functions6.1 Firmware Update from Storage DeviceiNotice!The rmware le can be obtained from the internet.Access only with storage de

36 366 Service Functions6.3 Save SettingsAccess only with storage device dened as Default storage !With the Save settings function the printer con

36376 Service Functions6.5 Reset Service CounterAccess only with service key inserted!The printer has total and service counters.• Total counter: T

38 386 Service Functions6.7 Save Log lesAccess only with storage device dened as Default storage !The function Save log les saves a le with the

38397 Pay-per-PrintPPP™ stands for „Pay-per-print“. cab established for distributors a secure internet portal, which can be used to transfer data for

4 4Important information and instructions in this documentation are designated as follows:Danger!Draws your attention to an exceptionally grave, impen

40 408 FTP Printer ManagementThe File Transfer Protocol (FTP) allows to manage and transfer les on the network via the Ethernet or WLAN interface .

40418 FTP Printer Management8.4 FTP Firmware UpdateFTP allows to carry out a rmware update:  Establish a FTP connection with the user name ftpadmi

42 429 Storage DevicesLabel descriptions, graphics, fonts, and database information can be saved for the long-term on memory media. iNotice!  Always

42439.4 WritingThe storage devices can be written to in several ways. The most functionally secure way is writing to the storage device via a data in

44 449.5.2 Printing Directory The Print directory function creates a list of the les stored on the default storage device.1. Insert printable mediu

444510 External KeyboardAn external keyboard or a compatible input device (e.g. barcode scanner) can be connected directly to the printer. Using an e

46 4610 External Keyboard10.3 Special Key FunctionsGeneral :[F1] Executes the Load label storage device function.[F2]Prints an additional label from

4647The cabFirmwareUpdater, which can be downloaded free of charge from the cab Website, offers an easy way to transfer rmware and PPP les from the

48 4812 IndexAActivating a PIN ...17ASCII dump mode ...8, 32BBackfeed...

452 Connecting Label Printer to ComputerChoose from the following options for connecting a computer to the label printer:• Direct connection to the

6 62 Connecting Label Printer to Computer2.1.1 Print Services Raw-IP and LPR/LPD in MS Windows  Install a standard TCP/IP port as additional port f

672.4 Setting Up a WLAN ConnectionTo set up a WLAN connection a WLAN USB Adapter (Part No. 5906225 ) is required.1. Connect the WLAN USB adapter to

8 83 Ofine Menu3.1 Structure of the Ofine MenuThe ofine menu contains setting options on several levels for conguring the label printer. In addi

893 Ofine Menu3.2 Navigating in the Ofine Menu  Select in the start display to start the Ofine menu.Return froma submenuLeaving theOffline men